Nilfisk-ALTO SW 750 User Manual Page 54
- Page / 76
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ENGLISH
USER MANUAL
16
146 3080 000(1)2006-10 A SW 750
DUST FILTER CLEANING AND INTEGRITY
CHECK, HOPPER GASKET CHECK
Drive the machine on a level ground.
Turn the main switch (1) to “0”.
Remove the hopper (9).
Loosen the knobs (A, Fig. 8).
Grasp the dust fi lter (B) as shown in the fi gure.
Remove the dust fi lter by turning it in the direction shown
by the arrow (A, Fig. 9) to disengage it from the pins (B),
then lower the fi lter to disengage it from the fi lter shaker
combs (C).
Remove the fi lter (A, Fig. 10) from the frame (B) by
disengaging the 3 rubber bands (C).
In an appropriate outdoor area, clean the fi lter by shaking
it on a level and clean surface, tapping the side (D)
opposite to the gasket (E).
Complete the cleaning procedure by using compressed
air (F) at maximum 6 Bars, blowing only from the side of
the gasket (E), at a minimum distance of 30 cm.
Do not use water or detergents to clean it, otherwise it
can be damaged.
Check the fi lter body for tears. If necessary, replace it.
Clean the bearing surface of the fi lter rubber gasket
(E) and check it for integrity and sealing capabilities. If
necessary, replace the fi lter.
Clean the bearing surface of the hopper gasket (D, Fig.
9) and check it for integrity and sealing capabilities. If
necessary, replace it.
Assemble in the reverse order of disassembly.
NOTE
Assemble the fi lter with the gasket (E, Fig. 10)
positioned as shown in the fi gure.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
S311357
Figure 8
S311358
Figure 9
S311359
Figure 10
A
B
A
B
B
D
A
C
D
A
F
B
C
E
- DEUTSCH BETRIEBSANLEITUNG 1
- ENGLISH USER MANUAL 1
- NEDERLANDS GEBRUIKSAANWIJZING 1
- 146 3080 000(1)2006-10 A 1
- INHALTSVERZEICHNIS 3
- EINLEITUNG 4
- AUSPACKEN/AUSLIEFERUNG 5
- SICHERHEIT 6
- MASCHINENBESCHREIBUNG 8
- ZUBEHÖRE/OPTIONEN 10
- TECHNISCHE DATEN 10
- SCHALTPLAN 11
- VOR DEM ANLASSEN DER MASCHINE 12
- NACH DER MASCHINENBENUTZUNG 13
- ERSTE BEDIENUNGSZEIT 13
- MASCHINE IN BETRIEB 13
- PRÜFUNG DES LADEGERÄTKABELS 14
- PRÜFUNG UND EINSTELLUNG DER 15
- SEITENBESENHÖHE 15
- HAUPTKEHRWALZENHÖHE 16
- BETRIEBSANLEITUNG 17
- REINIGUNG UND 18
- VOLLSTÄNDIGKEITSPRÜFUNG DES 18
- DES ABFALLBEHÄLTERS 18
- PRÜFUNG DER FLAPSHÖHE UND 19
- FUNKTIONSFÄHIGKEIT 19
- BATTERIELADUNG 19
- FEHLERSUCHE 20
- VERSCHROTTUNG 20
- TABLE DES MATIERES 21
- INTRODUCTION 22
- DEBALLAGE / LIVRAISON 23
- SECURITE 24
- MANUEL D'UTILISATION 25
- FRANÇAIS 25
- DESCRIPTION DE LA MACHINE 26
- ACCESSOIRES / OPTIONS 28
- CARACTERISTIQUES TECHNIQUES 28
- SCHEMA ELECTRIQUE 29
- UTILISATION 30
- MACHINE AU TRAVAIL 31
- VIDANGE DU CONTENEUR DECHETS 31
- ENTRETIEN 32
- BALAI LATERAL 33
- BALAI CENTRAL 34
- CONTROLE DE LA HAUTEUR ET DU 37
- FONCTIONNEMENT DES VOLETS 37
- CHARGEMENT DES BATTERIES 37
- DEPISTAGE DES PANNES 38
- MISE EN DECHARGE 38
- TABLE OF CONTENTS 39
- UNPACKING/DELIVERY 41
- GENERAL INSTRUCTIONS 42
- USER MANUAL 43
- MACHINE DESCRIPTION 44
- ACCESSORIES/OPTIONS 46
- TECHNICAL DATA 46
- WIRING DIAGRAM 47
- BEFORE MACHINE START-UP 48
- MACHINE OPERATION 49
- HOPPER EMPTYING 49
- AFTER MACHINE USE 49
- MACHINE LONG INACTIVITY 49
- FIRST PERIOD OF USE 49
- MAINTENANCE 50
- SIDE BROOM HEIGHT CHECK AND 51
- ADJUSTMENT 51
- MAIN BROOM HEIGHT CHECK AND 52
- CHECK, HOPPER GASKET CHECK 54
- BATTERY CHARGING 55
- TROUBLESHOOTING 56
- SCRAPPING 56
- INHOUDSOPGAVE 57
- INLEIDING 58
- MODIFICATIES EN VERBETERINGEN 59
- BEDRIJFSCAPACITEIT 59
- ALGEMENE OPMERKINGEN 59
- VEILIGHEID 60
- GEBRUIKSAANWIJZING 61
- NEDERLANDS 61
- BESCHRIJVING VAN DE MACHINE 62
- ACCESSOIRES / OPTIES 64
- TECHNISCHE EIGENSCHAPPEN 64
- ELEKTRISCH SCHEMA 65
- DE MACHINE STARTEN EN STOPPEN 66
- MACHINE IN BEDRIJF 67
- DE AFVALCONTAINER LEGEN 67
- NA GEBRUIK VAN DE MACHINE 67
- LANGE PERIODE VAN STILSTAND 67
- EERSTE GEBRUIKSPERIODE 67
- ONDERHOUD 68
- DE HOOGTE VAN DE ZIJBORSTEL 69
- CONTROLEREN EN AFSTELLEN 69
- DEMONTAGE/MONTAGE VAN DE 71
- HOOFDBORSTEL 71
- VAN DE AFVALCONTAINER 72
- VAN DE FLAPS 73
- ACCU OPLADEN 73
- STORINGEN LOKALISEREN 74
- VERWIJDERING 74
Related products and manuals for Floor Machine Nilfisk-ALTO SW 750
(124 pages)
(76 pages)
(52 pages)© 2020, manymanuals.com. All rights reserved. | 2.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals